BudBox 32010 (XS) Double Decker

RS-15 PS + Rasberry Pi 3 B

Buy Kit - $15

Mounting Hardware Required (Details)

  • 8x - #8 K Lock Nut
  • 12x - #8 Washer
  • 4x - #6 Self Tapping 1/2 in
  • 4x - #8 3 in Bolt
  • 4x - 3 in Spacer
  • 3x - M3 SM PS Screw
  • 4x - 4-40 Standoff
  • 4x - 4-40 K Lock Nut
  • 4x - 4-40 PCB Screw

About This Design

The smallest enclosure you can buy is perfect for SmartReceivers.

Using distributed layouts with F48 and Smart Receivers is an exciting development in DIY Christmas Lights. Now you can hide these tiny enclosures exactly where you need them to make cable management easier and eliminate power injection problems.


  • Fits up to 100w power supply and multiple small components such as Smart Receivers.
  • Double decker component deck allows for extra space for power and components
  • Fully customizable component holes using the JDeation Designer
  • Perfectly matched to mount to precisely to a BudBox 32010 Enclosure
  • Top plate has wire access on 3 sides
  • Bottom Plate Dimensions: 5.3in x 5.3in


  • Due to the limited height of the enclosure we do not recommend placing components on the top shelf that require a RJ45 (network) connection

Jdeation Featured Design

Design ID : JW5ZW5DV

Designer : jchancel

Assembly Instructions

Edit Design Buy Kit - $15

Mounting Hardware Required (Details)

  • 8x - #8 K Lock Nut
  • 12x - #8 Washer
  • 4x - #6 Self Tapping 1/2 in
  • 4x - #8 3 in Bolt
  • 4x - 3 in Spacer
  • 3x - M3 SM PS Screw
  • 4x - 4-40 Standoff
  • 4x - 4-40 K Lock Nut
  • 4x - 4-40 PCB Screw

Works With (Sold Seperately)

DIY Build & Assembly Instructions

Assembly instructions for - BudBox 32010 (XS) Double Decker

Please read these instructions fully and carefully before beginning your assembly. A little bit of learning and planning can make the difference between a easy great assembly and a hard mistake prone assembly.
The following assembly instructions contain both design specific and general assembly instruction which may not be specific to your design.

All of the JDeation designs are customizable using the JDeation Designer

View our detailed walkthrough video for instructions on how to use the JDeation Designer

The following pieces of hardware are required for assembly of Mounting Plate.

Most parts are available at home depot - all are available online.

  • Qty: 8 - #8 K Lock Nut
  • Qty: 12 - #8 Washer
  • Qty: 4 - #6 Self Tapping 1/2 in
  • Qty: 4 - #8 3 in Bolt
  • Qty: 4 - 3 in Spacer
  • Qty: 3 - M3 SM PS Screw
  • Qty: 4 - 4-40 Standoff
  • Qty: 4 - 4-40 K Lock Nut
  • Qty: 4 - 4-40 PCB Screw

Our Kits Make it Easy

Kits include acrylic, hardware and power supply brackets. Cheaper than you can buy at big box stores.

* example image only

The following plate fabrication instructions serve are general documentation for all mounting plate designs.

Step 1: Acquire Material

Acquire material to make your plates. Plastic or wood are good choices. The bellow instructions use 5mm plywood which was purchased from a local home depot. The material you choose MUST be 5mm or less in thickness.

Step 2: Print Design To Scale

Print your design on your home paper printer to scale.

On your design, click the download button and select PDF (Print). You must open the PDF in Adobe Reader to get the advanced print functions. Do not open the PDF in your browser. From the Adobe Reader print dialog box, select the following options.

Image of design printed to scale:

Step 3: Tape Design Together

Cut and Tape your designs together. Use the Adobe cross marks to align paper perfectly. It is important to spend time on this step and get alignment correct as a misaligned tape job will interfere with hole placements on layout.

Step 4: Apply Glue

Apply Gluestick to back of paper. We have had good success with repositionable glue sticks.

Step 5: Stick Design to Material

Apply paper design to wood. Line up two edges of design with two edges of wood if possible to reduce cutting.

Step 6: Drill Holes

Drill the black circles on the design. The following size drill bits are recommended. Also while not necessary it is recommended to use a brad point drill bit as it allows greater precision due to its sharp point on tip.

Screw Size Drill Size Typical uses
4/40 1/8" Component standoffs
#6 5/32" Self tapping screws for mounting to enclosure
#8 3/16" 3" and 4" Bolts for P.S. and Shelves
#10 7/32" 6" Bolts for P.S. and Shelves

NOTE: All Black lines on design are cut or drill lines. Red lines are just for helping create the design and for information useful to assembly

Step 7: Cut Out Design

Use a Jig Saw to cut out the straight black lines.

Our Kits Make it Easy

Kits include acrylic, hardware and power supply brackets. Cheaper than you can buy at big box stores.

* example image only

Step 1: Remove Protective Film

Remove plastic or paper film from both sides of acrylic or wood. Its much easier to do this now than after assembly.

NOTE: Occasionally the fabrication process will remove one or both sides. If you can see through the acrylic clearly then the film is gone.

Step 2: Attach Power Supply To Bottom Plate

Depending on the design, power supplies are either attached via mounting brackets, or screwed directly to the bottom plate. If your design requires the power supplies to be screwed to the bottom plate, attach them now using M3 or M4 screws.

Step 3: Attach Bolts to Bottom Plate

Attach bolts. The MTMACR8-72 has both 4” inch and 3” bolts, but not all designs have both. These should be inserted in the largest holes on the plate. See diagram below for bolt / washer / nut ordering. NOTE: Refer to your online design to find appropriate holes.


Step 4: Attach 4/40 Standoffs

Attach 4/40 standoffs and k-nuts to smallest holes. No washer is needed.


Step 5: Attach Components

Attach components to the standoff. No washer is needed.

Step 6: Insert Plate into Enclosure

Use self tapping screws to attach mounting plate to the enclosure. Holes should be medium size and in each corner of the mounting plate.

Step 8: Insert Upper Shelf

Insert upper shelf. Upper shelf sits directly on spacer and is attached with a K-Nut from the top. No washer is needed. You control the height of the second shelf by trimming the spacers. We recommend setting the height as high as possible to allow plenty of space for cable glands.

Step 9: Wire It Up

Wire it up and make it fancy.

Few tips:

  • Don’t tin your wires if inserting them into a screw down clamp. Solder will expand slightly and loosen the clamp.
  • Use fuse between power supplies and controllers. A lose connection could cause an arc and if unfused could damage your power supply or your controller and potentially cause a fire.
  • Make sure you use appropriate guage wire for the amperage you plan on needing. Small guage wire on high loads can cause greater voltage loss and in extreme cases start a fire.

View our timelapse of a JDeation Enclosure being wired up.

Step 10: Post Your Pics

Post a picture of your killer new build to facebook - make sure you tag JDeation Designer!

Use our contact page if you require assistance with your build.

Finished Build (outside of case)

Finished Build with wood plates (outside of case)